Black Widow Security BW FM 6150 Installationshandbuch PDF herunterladen

VEHICLE SECURITY SYSTEM

WITH REMOTE START & NETWORK INTERFACE

BEFORE INSTALLING THIS PRODUCT PLEASE READ

THIS INSTALLATION MANUAL THOROUGHLY!!

INSTALLATION MANUAL

Before You Begin

This system is intended for installation on vehi-

cles equipped with automatic transmissions and

electronic fuel injection only! DO NOT INSTALL

THIS SYSTEM INTO A MANUAL TRANSMIS-

SION VEHICLE AS IT COULD RESULT IN SERI-

OUS INJURY OR DEATH.

• This product must be installed by qualified

personnel according to these instructions and

and observing all safety features.

• Verify that the vehicle is equipped with elec-

tronic fuel injection and automatic transmis-

sion.

• Check to see if the vehicle is equipped with

any type of factory security system.

• Check to see if there is a pin switch for the

hood, if not one must be installed.

• Verify that the vehicle starts and idles prop-

erly before starting the installation.

• Always use a multi-meter when verifying

vehicle wiring.

• Before mounting the product, verify with the

customer the desired location for the valet

switch and LED.

• Set the Polarity Jumper inside the main unit

first. (see Jumper Settings)

Installation Instructions

Mounting System Module

Mount the system module under the dash

where it will be difficult for a potential thief to

locate the module, and away from moving parts

such as brake pedals, etc. Mount the extended

range receiver on the windshield in a location

that will not obscure the driver’s view.

Mounting Siren

Mount the siren in a suitable place under the

hood, away from hot and moving engine parts

such as manifolds, fan belts, etc. Make sure the

siren cannot be accessed from underneath the

vehicle or through the grill. Face the siren down

so that water cannot accumulate inside the

siren bell. Protect wires running through the

firewall using either tape or split loom tubing. If

a new hole is needed, protect the wire from

chaffing by installing a proper size grommet.

Mounting Shock Sensor

Secure the shock sensor to the steering col-

umn, thick wire harness or a dash brace, using a

wire tie. Make sure that the adjustment screw is

accessible for later testing and adjustment.

1 2 3 4 5 6 ... 15 16

Inhaltsverzeichnis

Seite 1 - INSTALLATION MANUAL

VEHICLE SECURITY SYSTEMWITH REMOTE START & NETWORK INTERFACEBEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!!INSTAL

Seite 2

10NEGATIVE PULSE LOCK SYSTEMPOSITIVE PULSE LOCK SYSTEMADDING ACTUATORS VACUUM LOCK SYSTEMDOOR LOCK WIRING DIAGRAMSREVERSE POLARITY LOCK SYSTEM

Seite 3

11TWO-STEP UNLOCKNEGATIVE PULSETWO-STEP UNLOCKPOSITIVE PULSETWO-STEP UNLOCKREVERSE POLARITYTWO-STEP UNLOCKADDING ACTUATORSOPTIONAL TWO-STEP UNLOCK WIR

Seite 4

12TROUBLESHOOTINGProblemAlarm does not operate.Alarm will not Passively Arm.Alarm will not enter CodeLearning Mode.Alarm chirps 4 times 5 sec-onds aft

Seite 5

13TROUBLESHOOTING CONTINUEDProblemRange is poor.Vehicle will not remote startand parking lights flash.Vehicle cranks and begins torun, then shuts off.

Seite 6

14LED INDICATIONSOn Solid = Valet ModeSlow Flash = System ArmedRapid Flash = Passive Arming2 Flashes = Shock Sensor4 Flashes = Door Trigger5 Flashes =

Seite 7

15INSTALLATION NOTES

Seite 8

16WIRING DIAGRAMJUMPER SETTINGSThe output polarity for the built-in parking light relay is deter-mined by the placement of the jumper on the 3 pins in

Seite 9 - RELAY WIRING DIAGRAMS

2High-Current Wire Connections:• RED WIRE #1 -Main power input; using thesupplied inline fuse holder, connect directly tothe vehicle’s battery or alt

Seite 10 - DOOR LOCK WIRING DIAGRAMS

3• RED WIRE - +12V Battery input #3. Connectthe red fused wire on the main harness to aconstant +12V source. This wire is the powerinput for the modul

Seite 11

4Programmable Features Step Function Button 1 Button 2 Button 31. Arming Mode Active Passive2. Auto Rearm Off On3. Normal/Silent Arming Normal Silent

Seite 12 - TROUBLESHOOTING

5Programmable Features1. Arming Mode. Select between manual arm-ing (Active) or automatic arming (Passive).2. Auto Rearm.Automatically rearms the sys-

Seite 13 - TROUBLESHOOTING CONTINUED

619. Cold Temperature Starting. Allows thevehicle to automatically start and run every 2hours or every hour for severe cold weather.20. Engine Start

Seite 14 - INSTALLATION NOTES

7Complete Default ResetFollowing this procedure will set all User andInstaller Programming Parameters to factorydefault settings.1. Enter System Progr

Seite 15

8Bypassing Factory Theft DeterrentSystemsMany newer vehicles are now factory-equippedwith anti-theft systems that use either a resistorcoded key or a

Seite 16 - JUMPER SETTINGS

9HORN HONK DIAGRAMSTRUNK RELEASE DIAGRAMRELAY WIRING DIAGRAMSSTARTER DISABLE / ANTI-GRIND OPTIONAL HEADLIGHT ACTIVATIONProgram the Auxiliary 2 output

Weitere Dokumente für Sicherheitszugriffskontrollsysteme Black Widow Security BW FM 6150

Um das Dokument anzuzeigen Black Widow Security BW FM 6150 Bedienungsanleitung

Black Widow Security BW FM 6150 Bedienungsanleitung (6 Seiten)

Black Widow Security BW FM 6150 Bedienungsanleitung (7 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Black Widow Security BW FM 6150 Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Sicherheitszugriffskontrollsysteme Black Widow Security BW FM 6150 herunter. Black Widow Security BW FM 6150 Installation manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Sicherheitszugriffskontrollsysteme Black Widow Security BW FM 6150

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Black Widow Security BW FM 6150